VINTAGE OWNER'S MANUALS, SERVICE MANUALS, BROCHURES AND PUBLICATIONS
Welcome to Automatic Ephemera, a library for historical research and education, sharing public domain documents relating to vintage products for
the home. You are viewing the low-resolution preview, high-resoultion versions are also available for most documents.
The scanning of all high-resolution documents is done at 300dpi with the utmost diligence and care to produce high quality .pdf files which have text
search capabilities built-in to bring modern convenience to vintage printed materials.
The high resolution also allows for close-up examination of all images on your computer monitor and in many cases makes
reading the text easier than the original document. Quality printers can print these documents nearly identically to the original document. Maintaining a library as such is a
time consuming and expensive venture, all materials have a small download fee to offset the library's many expenses.
In order to read these documents you need Adobe
Reader 7 or greater installed on your computer. Click here for samples of the Documents in our library.
If you have had any recent download purchases please see your download page.
If you have had any recent download purchases please see your download page.
1959 Frigidaire Dryer Service Tech-Talk (continued)
Page 25 of 32 First Page
< Back (Page 24)
> Next (Page 26)
...
Last (Page 32)
You are viewing a low-resolution preview. Available here is the high-res/32 page PDF version of this document ($2.64), most printers can output this nearly identically to the original document.
Automated Summary of Text on this Page:
INNER
DOOR PANEL DOOR SEAL
DOOR STRIKE
FRONT PANEL
INSULATION
DOOR LATCH MECHANISM
DOOR
SWITCH
HINGE TAPPING PLATE
LATCH BRACKET & MTG. SCREW
PANEL MOUNTING SCREWS (5)
DOOR TREADLE & MTG. SCREWS
DOOR HINGE
OUTSIDE DOOR PANEL
Figure 33
DCI-59 Door Panels, Front Panels and Components
Right Panel Only:
4. Remove the two panel-to-support bracket mounting screws at the lower portion of the panel.
5. Remove the one panel-to-frame mounting screw.
6. Remove and replace the panel.
Left Panel Only:
7. Remove the two panel support bracket-to-product base mounting screws.
8. Remove the one panel-to-frame mounting screw.
9. Remove the panel support bracket from the panel by removing two screws. Remove and replace the panel. Transfer the insulation.
Note: The right panel has a door switch mounted with two screws. Remove screws, pull electrical leads from terminals, and remove the switch. The left panel has a door latch arm and treadle assembly mounted to it. All parts are replaceable by removing the two latch mounting bracket screws, Figure 33.
K. Panels, Side -Replacement on DCI-59 Model:
1. Lay the dryer on its side or tilt sufficiently to remove the side panel bottom mounting screws arrowed in Figure 34.
2. With the dryer upright, remove the screws which mount the side panel to the rear cover panel.
3. Remove the top holddown screws at the rear of the dryer and position the top to clear the side panels" as needed.
4. Remove the side panel-to-top front support mounting screw.
5. Remove and replace the side panel.
Note: The left side panel only is insulated. The insulation should be transferred to the replacement panel.
L. Panels, Door and Strike-Replacement on DCI-59 Model-Figure 33:
1. Open the door and remove the four inner door
You are viewing a low-resolution preview. Available here is the high-res/32 page PDF version of this document ($2.64), most printers can output this nearly identically to the original document.
Automated Summary of Text on this Page:
INNER
DOOR PANEL DOOR SEAL
DOOR STRIKE
FRONT PANEL
INSULATION
DOOR LATCH MECHANISM
DOOR
SWITCH
HINGE TAPPING PLATE
LATCH BRACKET & MTG. SCREW
PANEL MOUNTING SCREWS (5)
DOOR TREADLE & MTG. SCREWS
DOOR HINGE
OUTSIDE DOOR PANEL
Figure 33
DCI-59 Door Panels, Front Panels and Components
Right Panel Only:
4. Remove the two panel-to-support bracket mounting screws at the lower portion of the panel.
5. Remove the one panel-to-frame mounting screw.
6. Remove and replace the panel.
Left Panel Only:
7. Remove the two panel support bracket-to-product base mounting screws.
8. Remove the one panel-to-frame mounting screw.
9. Remove the panel support bracket from the panel by removing two screws. Remove and replace the panel. Transfer the insulation.
Note: The right panel has a door switch mounted with two screws. Remove screws, pull electrical leads from terminals, and remove the switch. The left panel has a door latch arm and treadle assembly mounted to it. All parts are replaceable by removing the two latch mounting bracket screws, Figure 33.
K. Panels, Side -Replacement on DCI-59 Model:
1. Lay the dryer on its side or tilt sufficiently to remove the side panel bottom mounting screws arrowed in Figure 34.
2. With the dryer upright, remove the screws which mount the side panel to the rear cover panel.
3. Remove the top holddown screws at the rear of the dryer and position the top to clear the side panels" as needed.
4. Remove the side panel-to-top front support mounting screw.
5. Remove and replace the side panel.
Note: The left side panel only is insulated. The insulation should be transferred to the replacement panel.
L. Panels, Door and Strike-Replacement on DCI-59 Model-Figure 33:
1. Open the door and remove the four inner door
Page 25 of 32