VINTAGE OWNER'S MANUALS, SERVICE MANUALS, BROCHURES AND PUBLICATIONS
Welcome to Automatic Ephemera, a library for historical research and education, sharing public domain documents relating to vintage products for
the home. You are viewing the low-resolution preview, high-resoultion versions are also available for most documents.
The scanning of all high-resolution documents is done at 300dpi with the utmost diligence and care to produce high quality .pdf files which have text
search capabilities built-in to bring modern convenience to vintage printed materials.
The high resolution also allows for close-up examination of all images on your computer monitor and in many cases makes
reading the text easier than the original document. Quality printers can print these documents nearly identically to the original document. Maintaining a library as such is a
time consuming and expensive venture, all materials have a small download fee to offset the library's many expenses.
In order to read these documents you need Adobe
Reader 7 or greater installed on your computer. Click here for samples of the Documents in our library.
If you have had any recent download purchases please see your download page.
If you have had any recent download purchases please see your download page.
1959 Frigidaire Dryer Service Tech-Talk (continued)
Page 26 of 32 First Page
< Back (Page 25)
> Next (Page 27)
...
Last (Page 32)
You are viewing a low-resolution preview. Available here is the high-res/32 page PDF version of this document ($2.64), most printers can output this nearly identically to the original document.
Automated Summary of Text on this Page:
B474
Figure 34
DCI-59 Cabinet-to-Base Mounting Screws
panel mounting screws and fiber washers.
2. Remove the two strike-to-inner door panel mounting screws and fiber washers.
3. Remove the strike, inner door panel, circular seal and seal retainer.
4. Remove the two hinge-to-door mounting screws at the top of the door. Remove the gasket and tapping plate.
5. Pull the outer door panel from the bottom pivot and remove the panel.
6. Remove the two bottom hinge mounting screws. Remove the gasket and tapping plate.
7. Remove and replace the outer panel.
DD-59, DCD-59 and DI-59 Models - Figure 21:
1. Remove the top mounting screws, at rear of dryer, and slide the top back to permit access to the inside of the shell, at front. (Steps A-8 and B-22.)
2. Open the door and remove the two hinges with door from cabinet-four screws, two speed nuts behind front cabinet shell, and two gaskets.
3. Remove the door hinge and all parts.
4. Remove the two strike mounting screws and remove the strike from the door.
Nole: The strike can be removed, if necessary, only with the door open.
5. Remove the four inner panel-to-outer panel mounting screws. Remove the inner panel and clothes deflector as an assembly.
6. Remove the three deflector mounting screws. Remove deflector.
7. Remove the five speed nuts from the outer panel
which are used for mounting the inner panel.
8. Remove the two hinges from the outer panel-four screws, two speed nuts and two gaskets.
9. Replace the outer panel.
M. Filtrator and Condensate Pan -Replacement on DCI-59 Model -Figure 35:
1. Remove the Filtrator.
2. Remove the four, front trim mounting screws from the Filtrator.
3. Remove and replace the trim if necessary.
4. Remove the two handle mounting screws.
5. Remove and replace the handle or the Filtrator. Note: The two tube guards are not furnished with the replacement Filtrator and must be transferred from the old to the new.
6. Remove the condensate pan.
7. Remove four front trim to pan mounting screws.
8. Remove the two gasket and gasket mounting bracket screws.
9. Replace any of the following:
a. Pan trim.
b. Front gasket.
c. Trim and gasket mounting bracket.
d. Trim mounting speed nuts.
N. Lint Tray and Screen - Replacement on DD-59, DCD-59 and DI-59 Models-Figure 36:
1. Pull out the tray.
2. Remove the screen from the tray frame. The screen has an elastic edge to permit easy removal for cleaning or replacement.
3. Remove the two handle mounting screws and remove the handle.
4. Replace necessary parts.
Note: Replacement tray frame is furnished with seals cemented in place.
O. Catch, Lint Tray - Replacement on DD-59, DCD-59 and DI-59 Models:
1. Pull out the tray.
2. Remove the two catch mounting screws and lock-washers located inside the tray opening.
Hint: A two-hole speed nut, Figure 22, is used on the back side of the chamber-accessible only if top and drum are removed. Therefore, first remove only the rear screw and lockwasher, then turn catch from position to permit mounting a new catch with rear screw and washer. Then remove front screw and lockwasher, remove whole catch and finish mounting a new catch. One mounting screw must always be in position to prevent loss of speed nut.
P. Hose and Nozzle, Sprinkler-Removal on DI-59 and DCI-59 Models -Figures 6 and 7:
1. Remove the dryer rear cover.
2. Pull the hose and nozzle from its position in the drum shaft.
3. Pull the nozzle from the tube. Replace if necessary.
You are viewing a low-resolution preview. Available here is the high-res/32 page PDF version of this document ($2.64), most printers can output this nearly identically to the original document.
Automated Summary of Text on this Page:
B474
Figure 34
DCI-59 Cabinet-to-Base Mounting Screws
panel mounting screws and fiber washers.
2. Remove the two strike-to-inner door panel mounting screws and fiber washers.
3. Remove the strike, inner door panel, circular seal and seal retainer.
4. Remove the two hinge-to-door mounting screws at the top of the door. Remove the gasket and tapping plate.
5. Pull the outer door panel from the bottom pivot and remove the panel.
6. Remove the two bottom hinge mounting screws. Remove the gasket and tapping plate.
7. Remove and replace the outer panel.
DD-59, DCD-59 and DI-59 Models - Figure 21:
1. Remove the top mounting screws, at rear of dryer, and slide the top back to permit access to the inside of the shell, at front. (Steps A-8 and B-22.)
2. Open the door and remove the two hinges with door from cabinet-four screws, two speed nuts behind front cabinet shell, and two gaskets.
3. Remove the door hinge and all parts.
4. Remove the two strike mounting screws and remove the strike from the door.
Nole: The strike can be removed, if necessary, only with the door open.
5. Remove the four inner panel-to-outer panel mounting screws. Remove the inner panel and clothes deflector as an assembly.
6. Remove the three deflector mounting screws. Remove deflector.
7. Remove the five speed nuts from the outer panel
which are used for mounting the inner panel.
8. Remove the two hinges from the outer panel-four screws, two speed nuts and two gaskets.
9. Replace the outer panel.
M. Filtrator and Condensate Pan -Replacement on DCI-59 Model -Figure 35:
1. Remove the Filtrator.
2. Remove the four, front trim mounting screws from the Filtrator.
3. Remove and replace the trim if necessary.
4. Remove the two handle mounting screws.
5. Remove and replace the handle or the Filtrator. Note: The two tube guards are not furnished with the replacement Filtrator and must be transferred from the old to the new.
6. Remove the condensate pan.
7. Remove four front trim to pan mounting screws.
8. Remove the two gasket and gasket mounting bracket screws.
9. Replace any of the following:
a. Pan trim.
b. Front gasket.
c. Trim and gasket mounting bracket.
d. Trim mounting speed nuts.
N. Lint Tray and Screen - Replacement on DD-59, DCD-59 and DI-59 Models-Figure 36:
1. Pull out the tray.
2. Remove the screen from the tray frame. The screen has an elastic edge to permit easy removal for cleaning or replacement.
3. Remove the two handle mounting screws and remove the handle.
4. Replace necessary parts.
Note: Replacement tray frame is furnished with seals cemented in place.
O. Catch, Lint Tray - Replacement on DD-59, DCD-59 and DI-59 Models:
1. Pull out the tray.
2. Remove the two catch mounting screws and lock-washers located inside the tray opening.
Hint: A two-hole speed nut, Figure 22, is used on the back side of the chamber-accessible only if top and drum are removed. Therefore, first remove only the rear screw and lockwasher, then turn catch from position to permit mounting a new catch with rear screw and washer. Then remove front screw and lockwasher, remove whole catch and finish mounting a new catch. One mounting screw must always be in position to prevent loss of speed nut.
P. Hose and Nozzle, Sprinkler-Removal on DI-59 and DCI-59 Models -Figures 6 and 7:
1. Remove the dryer rear cover.
2. Pull the hose and nozzle from its position in the drum shaft.
3. Pull the nozzle from the tube. Replace if necessary.
Page 26 of 32